-
1 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
2 длительный допустимый ток
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-английский словарь нормативно-технической терминологии > длительный допустимый ток
-
3 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
4 опасность
1) General subject: (воображаемое)(мнимая) a lion in the path (in the way), danger, death-trap, gravity, gravity (болезни, положения и т.п.), harmfulness, imminence, jeopardy, lion in the way, menace, peril, pitfall, radiohazard, risk, riskiness, severity (болезни, ранения и т. п.), storm cloud, the spot, unsafety, harm's way2) Biology: hazard3) Naval: obstruction4) Ironical: lion in the path6) Law: dangerousness, insecurity7) Diplomatic term: danger of something (чего-л.), gravity (положения и т.п.), menace of something (чего-л.)8) Jargon: rumble9) Patents: threat10) Business: venturousness11) Sakhalin energy glossary: hazard( Something with the potential to cause harm, for example a tank containing flammable material is a fire hazard.)12) Automation: (потенциальная) hazard13) Aviation medicine: hazard chance14) Pharmacy: (при контроле биозагрязнений) hazard (потенциальный источник возникновения ущерба) -
5 убыток
loss, damage; мн. material losses* * ** * *loss, damage; material losses* * *damagedetermentdetrimentdisadvantageharminjurylesionloselosssacrificescathewastagewaste -
6 значительный ущерб
1) Military: significant damage2) Engineering: significant harm3) Accounting: heavy damage4) Ecology: substantial damage5) Business: extensive damage, material damage, severe damage, major damageУниверсальный русско-английский словарь > значительный ущерб
-
7 опасный фактор
1) Engineering: hazard2) Sakhalin energy glossary: hazard( Something with the potential to cause harm, for example a tank containing flammable material is a fire hazard.) -
8 риск
1) General subject: adventure, cast, chance, exposure (и), flutter (обыкн. в азартных играх), hazard, jeopardy, peril, risk, throw, danger2) Naval: venture3) Colloquial: lucky dip4) Rare: die5) Law: case of the die, cast of the die, hazard to life6) Psychology: risk-taking7) Oil: taking a chance, taking the risk8) Sakhalin energy glossary: hazard( Something with the potential to cause harm, for example a tank containing flammable material is a fire hazard.), risk (The likelihood of a specified undesired event occurring within a specified period or in specified circumstances. This is typically expressed as fatalities per year.)10) Quality control: hazard chance (опасности)11) oil&gas: measure of danger, probability of potential accidents, mathematical expectation of damage, risk = likelihood x consequences = L*C -
9 X75
-
10 X75.9
-
11 вещество, загрязняющее воздух
вещество, загрязняющее воздух
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
air pollutant
Any pollutant agent or combination of such agents, including any physical, chemical, biological, radioactive substance or matter which is emitted into or otherwise enters the ambient air and can, in high enough concentrations, harm humans, animals, vegetation or material. (Source: LEE / TOE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > вещество, загрязняющее воздух
-
12 защита природы
защита природы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
nature protection
Precautionary actions, procedures or installations undertaken to prevent or reduce harm to the elements of the material world that exist independently of human activity. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > защита природы
-
13 вещество, загрязняющее воздух
вещество, загрязняющее воздух
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
air pollutant
Any pollutant agent or combination of such agents, including any physical, chemical, biological, radioactive substance or matter which is emitted into or otherwise enters the ambient air and can, in high enough concentrations, harm humans, animals, vegetation or material. (Source: LEE / TOE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > вещество, загрязняющее воздух
-
14 защита природы
защита природы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
nature protection
Precautionary actions, procedures or installations undertaken to prevent or reduce harm to the elements of the material world that exist independently of human activity. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > защита природы
-
15 вещество, загрязняющее воздух
вещество, загрязняющее воздух
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
air pollutant
Any pollutant agent or combination of such agents, including any physical, chemical, biological, radioactive substance or matter which is emitted into or otherwise enters the ambient air and can, in high enough concentrations, harm humans, animals, vegetation or material. (Source: LEE / TOE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > вещество, загрязняющее воздух
-
16 защита природы
защита природы
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
nature protection
Precautionary actions, procedures or installations undertaken to prevent or reduce harm to the elements of the material world that exist independently of human activity. (Source: RHW)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > защита природы
См. также в других словарях:
harm — ► NOUN 1) physical injury, especially that which is deliberately inflicted. 2) material damage. 3) actual or potential ill effect. ► VERB 1) physically injure. 2) have an adverse effect on. ● … English terms dictionary
harm — noun physical injury, especially that which is deliberately inflicted. ↘material damage. ↘actual or potential ill effect. verb physically injure. ↘have an adverse effect on. Phrases out of harm s way in a safe place. Origin OE hearm (n.),… … English new terms dictionary
Victimless crime — A victimless crime is a term used to refer to actions that have been ruled illegal but do not directly violate or threaten the rights of another individual. It often involves consensual acts in which two or more persons agree to commit a criminal … Wikipedia
witchcraft — No topic in folklore has caused more argument than witchcraft. However, the work of historians over the past 30 years has disentangled various levels of meaning within the word itself, and analysed the social context for accusations. The… … A Dictionary of English folklore
Time is of the essence — is a term in contract law which indicates that the parties to the agreement must perform by the time to which the parties have agreed if a delay will cause material harm, such as the court s interpretation in the case of Foundation Development… … Wikipedia
evil — adj. & n. adj. 1 morally bad; wicked. 2 harmful or tending to harm, esp. intentionally or characteristically. 3 disagreeable or unpleasant (has an evil temper). 4 unlucky; causing misfortune (evil days). n. 1 an evil thing; an instance of… … Useful english dictionary
hurt — I. verb (hurt; hurting) Etymology: Middle English, probably from Anglo French hurter to strike, prick, collide with, probably of Germanic origin; akin to Old Norse hrūtr male sheep Date: 13th century transitive verb 1. a. to inflict with physical … New Collegiate Dictionary
Code of Personal Status (Tunisia) — The Code of Personal Status (CPS) (Arabic: مجلة الأحوال الشخصية) is a series of progressive Tunisian laws aiming at the institution of equality between women and men in a number of areas. It was promulgated by beylical decree on August 13, 1956… … Wikipedia
the evil eye — a gaze or stare superstitiously believed to cause material harm he gave me the evil eye as I walked down the corridor * * * the evil eye : a look that is thought to be able to harm someone He gave her the evil eye. • • • Main Entry: ↑ … Useful english dictionary
the evil eye — ► the evil eye a gaze superstitiously believed to cause material harm. Main Entry: ↑evil … English terms dictionary
environmental works — ▪ civil engineering Introduction infrastructure that provides cities and towns with water supply, waste disposal, and pollution control services. They include extensive networks of reservoirs, pipelines, treatment systems, pumping stations … Universalium
